What is leak alert
Leak alert is a series of water detectors that alert you to a leak. Leak AlertLeak Alert WiFiLeak Alert + LEDLeak Alert X
FAQs
Do Zircon stud finders work on lath and plaster walls?
Basic Zircon StudSensor™ stud finders with only Stud Scan and/or DeepScan® mode are not recommended for lath and plaster walls. However, MultiScanner™ models with Metal Scan mode (or a dedicated metal finder) can be used to locate the pattern of nails or screw heads attaching the wood lath to the studs. The nails or screws should be found …
What kind of batteries do Zircon Leak Alert™ water detectors use?
Zircon offers a complete line of Leak Alert™ water detectors for your needs. The Leak Alert™ and Leak Alert™ LED! water detectors require one brand new 9V alkaline battery (with an extended expiration date). The Leak Alert™ WiFi smart water detector requires one 3V (CR123A / CR17345) lithium battery (primary – not rechargeable). Please be sure to install the …
What kind of batteries do Zircon stud finders use?
Most Zircon StudSensor™ and MultiScanner™ stud finders require one brand new alkaline 9V battery (with an extended expiration date) for proper operation. Please be sure to refer to the instructions for the specific model you have. Note: The Wood Stud SuperScan® requires two AA batteries and the MultiScanner™ x85 requires three AAA (LR03) batteries.
What is Zircon’s product warranty?
Zircon Corporation (“Zircon”) warrants to the original purchaser (or original user by gift) that this product will be free from defects in materials and workmanship for its useful life (not to exceed twenty years from date of purchase). For more information, visit https://www.zircon.com/warranty-registration/ or call 1-800-245-9265 (Mon – Fri 8 AM – 5 PM PST, …
What is Zircon’s contact information?
Zircon Corporation is located in the Silicon Valley, California USA. Zircon Corporation1580 Dell AvenueCampbell, California 95008, U.S.A. Zircon Customer Service is available Monday through Friday, 8:00 AM to 5:00 PM Pacific Time. Closed 2025: 1/1, 2/17, 5/26, 7/4, 9/1, 11/27-11/28, 12/25-12/26 Main Phone Line & General Inquiries: 408-963-4550Technical Support: 1-800-245-9265Fax: 408-963-4597 General Info: info@zircon.com*Technical Support: techsupport@zircon.comSales: sales@zircon.comMedia Support: marketing@zircon.com * Please be …
How do I change the battery in my stud finder?
Zircon stud finders do not require the removal of any screws to install batteries. Do not unscrew the tool. This will release the components inside and cause it to work improperly. Tip Minute on How to Change Battery For the appropriate battery installation steps for a specific model, please click here, give us a call:1-800-245-9265, Monday through Friday, …
How do I reassemble my StudSensor™ stud finder if I took the screw off of the back?
With the screw still off, take the battery cover off and place the tool flat on a table. Carefully take the top case off to reveal the circuit board inside. Make sure everything is aligned correctly and looks square. Check that the battery spacer (the plastic part with two holes) is sitting in front of …
Can I use Zircon stud finders on the exterior of my home, through siding, or roof shingles?
No, Zircon StudSensor™ stud finders and MultiScanner™ wall scanners are designed and recommended for interior use only. Tip Minute with more info More info – Read the Stuck on Stucco Blog
How do I calibrate my StudSensor™ or MultiScanner™ stud finder?
Zircon stud finders are designed to be as effortless as possible. Place the stud finder flat against the wall, press and hold the power button, and wait for 1-2 seconds. The tool automatically calibrates to the wall’s surface. If there is a calibration error, or if you have started over a stud, the tool will …